Results 1 to 11 of 11
  1. Default Sight Partially Blocked by Riser

    Bow: Diamond SB-1
    Rest: Trophy Taker Smackdown Pro
    Set up by pro shop

    I paper tuned (at 10 ft) and the rest needed a lot of adjustment to get the arrow tip holes inside the fletching. I then nock tuned to get a little cleaner paper tears. I also put lipstick on the fletching to make sure I wasn't hitting the cables or rest housing while on the way out.

    When I took it out to 20 and 30 yards I needed to move the sight's windage quite a bit and now the sight housing is about 1/3 blocked by the riser. I can see the pins fine, but this doesn't seem right.

    I plan to go back to the shop this weekend, but wanted to see if anyone has any ideas.

    As far as I can tell I'm not adding torque to the bow. Even if I draw back and grip with my thumb and index finger I get the same results.

  2. #2
    Join Date
    Dec 2015
    Location
    Socialist Republic of Kalistan
    Posts
    144

    Default

    You can get the rest so far off, that it is still paper tuning.

    When looking down the shaft from behind, is the arrow resting on the rest close to dead center between the limbs?

  3. #3

    Default

    Most manufacturers give a centershot measurement in the specs. This is a starting point. Set your centershot to that or even eyeball the string down the arrow from behind...this is a starting point. Now do a walk back test or modified french tuning from there.

  4. #4
    Join Date
    Mar 2012
    Location
    Somewhere in the basalt rocks
    Posts
    4,565

    Default

    If you have to move a rest that far out of center shot to “tune” it, something is seriously wrong. Either your bow is out of spec or you are torquing the heck out of something.

    Edit: I just looked at these, you need to go back to the shop and reset all specs, then have them help you yoke tune it.
    Fear the beard....

  5. Default

    Since I'm still fairly new to archery, I will give the benefit of the doubt and assume I'm adding torque. After doing more research I think I am putting uneven pressure on the grip with my bow hand. Not necessarily twisting the bow, but the draw is not directly in line with center. I will try to paper tune again tomorrow and see if anything changes. I'll report back then.

  6. #6
    Join Date
    Nov 2009
    Location
    South East Colorado
    Posts
    8,216

    Default

    Go to a bow shop and have them critique your form. They can tell you for sure if you're torquing the bow and can give you a few pointers. Being new to archery I'd hate to see you making a mistake right from the get go that can get compounded over time.
    I'm an addict...archery, rifles, shotguns, handguns, muzzleloaders, hunting, fishing, fly fishing..and I don't want rehab

    CWEH...Colorado's Worst Elk Hunter 2007-2017 (but I'm still damned sexy) 10 years of consistency!!

  7. #7
    Join Date
    Mar 2012
    Location
    Somewhere in the basalt rocks
    Posts
    4,565

    Default

    It’s easy to tell if you are torquing the grip. Have someone stand behind you at full draw. The string should come straight off the cams. If it’s at any sort of an angle you are applying torque.
    Fear the beard....

  8. Default

    UPDATE:

    Just got back from the shop. I'm happy to say we identified the problem. There were a few smaller issues we identified. I had a little too much facial pressure on the bow so we resolved that by decreasing my draw by half an inch. I was torquing the bow a little bit, but that was not the source of the bad tears.

    The main issue was the arrow rest. I have a trophy taker smackdown pro and it was not rising all the way at full draw. There was still tension in the string due to the limbs not flexing enough. We retied it further out on the limb and that seemed to fix that problem. A little adjustment and I was getting my bullet holes.

    The rest was also moved back to its original position, thus moving the sight back out and not blocked at all.

    Thanks everyone for replying to this thread.
    Last edited by NV_PackMule; 04-13-2018 at 08:16 PM.

  9. #9
    Join Date
    Nov 2009
    Location
    South East Colorado
    Posts
    8,216

    Default

    Awesome!! I'm glad it was nothing major.
    I'm an addict...archery, rifles, shotguns, handguns, muzzleloaders, hunting, fishing, fly fishing..and I don't want rehab

    CWEH...Colorado's Worst Elk Hunter 2007-2017 (but I'm still damned sexy) 10 years of consistency!!

  10. #10
    Join Date
    Mar 2012
    Location
    Somewhere in the basalt rocks
    Posts
    4,565

    Default

    Outstanding.
    Fear the beard....

  11. #11
    Join Date
    Dec 2015
    Location
    Socialist Republic of Kalistan
    Posts
    144

    Default

    Now shoot the pudding out of it!

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •