Page 3 of 3 FirstFirst 123
Results 51 to 67 of 67

Thread: Getting Started

  1. Default

    Quote Originally Posted by Addicting View Post
    I went to Cabela's last night and looked at bullets, made me realize this is going to get expensive. A lot of the posts I see are different loads and different powders leading to a large list of combinations. Looking at quantity of issue of bullets and cost to find the one that the gun likes is going to take a bit. Any recommendations on how not to have 20 partial boxes of different bullets laying around waiting to never get used? (besides lots of range time shooting)
    I would suggest looking at cup and core bullet's, they are about half what the premium bullet's are! And little known fact, choose them properly and they do as well as any premium bullet.

    Never liked the Lee scale but maybe it's changed, I don't know. Lee dies do the same thing as Redding, did I say that? Well I have both and they do! But admit to liking the Redding better. This whole business of reloading really get's out of hand sometime's. You can spend as much as you want or very little and do the same job! Once you get going good you can decide what you really want, you likely won't need it but you will want it! Once your going watch gun shows. Lot of overpriced stuff there but you really don't need to buy it. Last gun show I went to I got 100 new Win 243 case's for $25 and 1000, one brick, of CCI 200's for $20!

  2. #52

    Default

    Quote Originally Posted by Addicting View Post
    I ordered the RCBS master supreme kit with the intention of loading the 130g Accubonds for my Creedmoor. Problem is that I wonder and daydream too much. After looking at the Barnes and Sencar, I know I won’t be happy until I shoot them. I have a feeling I am going to have little to no self control in staying with 1 bullet, 1 powder, and 1 primer.
    Then just change your "worry" to an expectation that you may have a bunch of partial bullet boxes! I've been very happy with Scenars out of my 260 on pronghorn.

  3. #53
    Join Date
    Aug 2017
    Location
    Eden Prairie, MN
    Posts
    362

    Default

    Quote Originally Posted by Brian in Montana View Post
    I tend to have an aversion to the trendy. ��
    this +1
    "Freedom is NOT Free"

  4. #54

    Default

    I came across a YouTube vid the other night of a guy using his Lee press to resize .308 brass to 7mm-08. Something about that just doesn't really seem like a great idea. Is that a safe thing to do and isn't the 7-08 cartridge a little longer than the .308?
    Act justly, love mercy, walk humbly.

    Micah 6:8

  5. #55
    Join Date
    Aug 2017
    Location
    Eden Prairie, MN
    Posts
    362

    Default

    Quote Originally Posted by Brian in Montana View Post
    I came across a YouTube vid the other night of a guy using his Lee press to resize .308 brass to 7mm-08. Something about that just doesn't really seem like a great idea. Is that a safe thing to do and isn't the 7-08 cartridge a little longer than the .308?
    They are essentially the same below the neck. Necking down will leave thicker/longer neck, so trimming and thinning the neck gets them to spec. Seems like a lot of extra work, but see no reason that they would be unsafe -- as I understand, this is how 7mm08 was developed in the first place.
    "Freedom is NOT Free"

  6. #56

    Default

    OK, so with regard to cleaning brass. How important is it to use a tumbler to clean brass that has been fired only once before? For example, factory ammo that has been shot once at the range and put right in a container - does that brass really need to be run through a tumbler before reloaded?
    Act justly, love mercy, walk humbly.

    Micah 6:8

  7. #57

    Default

    Quote Originally Posted by Brian in Montana View Post
    OK, so with regard to cleaning brass. How important is it to use a tumbler to clean brass that has been fired only once before? For example, factory ammo that has been shot once at the range and put right in a container - does that brass really need to be run through a tumbler before reloaded?
    Nope. mtmuley

  8. #58
    Join Date
    Mar 2012
    Location
    Somewhere in the basalt rocks
    Posts
    4,142

    Default

    I don’t even own a tumbler.
    Fear the beard....

  9. #59
    Join Date
    Jan 2001
    Location
    Laramie, WY
    Posts
    9,598

    Default

    Quote Originally Posted by JLS View Post
    I don’t even own a tumbler.
    I didn't for a long time either, but now wonder how I lived without one.
    "...the world outside, which my brother and I soon discovered, was full of bastards, the number increasing rapidly the farther one gets from Missoula, Montana." -Norman Maclean

    "They were still so young they hadn't learned to count the odds and to sense they might owe the universe a tragedy"
    -Norman Maclean

  10. Default

    Quote Originally Posted by Brian in Montana View Post
    I came across a YouTube vid the other night of a guy using his Lee press to resize .308 brass to 7mm-08. Something about that just doesn't really seem like a great idea. Is that a safe thing to do and isn't the 7-08 cartridge a little longer than the .308?
    At one time I was low on 243 case's and couldn't find any. Ran some military 308 case's through the 243 die and necked them down in one pull. Didn't need to do anything but trim to length.

  11. #61

    Default

    Picked up my bench yesterday and had to switch my RCBS order over to Amazon to get it here by Christmas and for the rebate program. Just need to source the components. Where normally has the best deals on bullets and powder? Midway?

  12. #62
    Join Date
    Mar 2012
    Location
    Somewhere in the basalt rocks
    Posts
    4,142

    Default

    Or Midsouth. I usually buy powder local during load development, then I stock up on my way through Missoula.
    Fear the beard....

  13. #63
    Join Date
    Jan 2001
    Location
    Laramie, WY
    Posts
    9,598

    Default

    Quote Originally Posted by Addicting View Post
    Picked up my bench yesterday and had to switch my RCBS order over to Amazon to get it here by Christmas and for the rebate program. Just need to source the components. Where normally has the best deals on bullets and powder? Midway?
    For nosler bullets, the seconds from shooters pro shop are hard to beat...I usually buy 500-1k at a time when they have what I need. Bullets don't go bad.
    "...the world outside, which my brother and I soon discovered, was full of bastards, the number increasing rapidly the farther one gets from Missoula, Montana." -Norman Maclean

    "They were still so young they hadn't learned to count the odds and to sense they might owe the universe a tragedy"
    -Norman Maclean

  14. #64

    Default

    BuzzH, have you had any issues the blemish Accubonds? I see they say they are cosmetic and won’t effect performance. Thier price point is pretty hard to pass up especially with the military discount.

  15. #65
    Join Date
    Oct 2009
    Location
    In the Sagebrush (Dillon, MT)
    Posts
    2,277

    Default

    Quote Originally Posted by Addicting View Post
    BuzzH, have you had any issues the blemish Accubonds? I see they say they are cosmetic and won’t effect performance. Thier price point is pretty hard to pass up especially with the military discount.
    I know your question was directed to Buzz but I've been shooting Nosler seconds exclusively in 5 or 6 different rifles. Never had an issue except regret that I didn't stock up on more 7mm Accubonds. Most recent ShootersProShop purchase was 182 grain 30cal Etips...picked them up for about $0.25 each which is 1/3 the retail price.
    Last edited by Mthuntr; Yesterday at 08:29 PM.

  16. #66
    Join Date
    Jan 2001
    Location
    Laramie, WY
    Posts
    9,598

    Default

    Quote Originally Posted by Addicting View Post
    BuzzH, have you had any issues the blemish Accubonds? I see they say they are cosmetic and won’t effect performance. Thier price point is pretty hard to pass up especially with the military discount.
    Not at all...in fact, I cant even find a blemish on any of them. Sometimes, they also have good deals on the over-runs, that I don't believe are seconds.

    Been shooting them for a long time in .22, .243, .25, .284, .30, and .338 without a single problem...probably the last 15 years or so?

    At the price point, I don't mind shooting steel with them, using them for load development...really like practicing and hunting with the same bullet.

    I've also never read anything about anyone having any kind of trouble with them.
    "...the world outside, which my brother and I soon discovered, was full of bastards, the number increasing rapidly the farther one gets from Missoula, Montana." -Norman Maclean

    "They were still so young they hadn't learned to count the odds and to sense they might owe the universe a tragedy"
    -Norman Maclean

  17. #67

    Default

    Powder is best bought locally unless you are buying in large quantities due to the hazmat fee.

    Most all my larger centerfire bullets are bought through SPS.

Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •