Search results
-
S
Sell or Send back first?
Forrest, You still haven't gotten that brake off yet??? -
S
Nosler AB LR 168gr bullets in a 280AI
Yeah, it pretty much just holed through. 115gr Ballistic Tips from my 257Roberts did more internal damage at a further distance.- std7mag
- Post #36
- Forum: Ammunition and Reloading
-
S
Henry’s 45/70
No issues with the stock. I haven't put a full box of ammo through it yet. -
S
Henry’s 45/70
I have the single shot, brass in 45-70. I was kinda bummed with Henry about it being a break open action, instead of a falling block like a Ruger #1. Sights are kinda hard for my old eyes to see. Thinking of putting a red dot on it. Shooting Federal ammo right now. 325gr(?). It's... -
S
Need some input on these scopes.
I got the Ziess V4 you mentioned. The zero stop was a bit of a PITA to set. But once set, has worked well. Glass is good, as you'd expect from Ziess. I got the 93(?) MOA reticle. Euro Optics had it on sale when I got mine. $699. -
S
Nosler AB LR 168gr bullets in a 280AI
That's the problem. It didn't mushroom. Bullet sized hole going in, bullet sized hole going out. Luckily, shock & hole in vital area brought it down. The ABLR are supposed to mushroom starting at 1,300fps. So a hit at 3,000fps should have opened up nicely. But no.- std7mag
- Post #18
- Forum: Ammunition and Reloading
-
S
Ebonizing Walnut
Looking good @nhenry!! And bravo to you for experimenting! If I may derail for a minute to help anyone else looking to do some self gunsmithing. @BrentD suggestion to wrap tape around where nhenry was going to make his cut. This is an oldtimers trick to help keep the wood fibers from flaying... -
S
custom rifle suggestions
If it's a Defiance An-Ti action, then is it really a Model 7?? At that point it's really a full on custom rifle. -
S
50 or 45 caliber inline?
Ok, hadn't thought of that!! 1:20 twist rate.- std7mag
- Post #22
- Forum: Muzzleloaders
-
S
Seized Cylinder on Revolver
My friend (he's done black powder all his life) uses hot (boiling) water and vinegar to break through the nasty from an uncleaned revolver. He's gotten several to shooting condition using this.- std7mag
- Post #8
- Forum: Muzzleloaders
-
S
50 or 45 caliber inline?
Well, i ended up getting a Traditions (can't recall the model) in 45. Put an EGW base on it with a 3-9X40 Crimson Trace Hardline scope. Interestingly enough, Traditions says NOT to use patched round ball or Minnie ball in it. Sabot only. I have an order in with Cutting Edge Bullets for...- std7mag
- Post #20
- Forum: Muzzleloaders
-
S
Ready for a new 7 mag load
I'd tend to agree with 300stw. Vihtavouri N550, N565, N570, IMR7828, Retumbo, H1000 would do you better than IMR4350. The 4831 would be close to RL19 burn wise. Not the highest velocity, but decent accuracy. RL23 and RL26 are good for the bullet weight, but finding any is hard to say the...- std7mag
- Post #45
- Forum: Ammunition and Reloading
-
S
custom rifle suggestions
I do almost all of my own work. But the devil is in the details. @p_ham has shown the attention to detail that merits the accolades he has received. -
S
Ready for a new 7 mag load
@perma, So!!?? Did you find a load for the 7mm Rem Mag??- std7mag
- Post #42
- Forum: Ammunition and Reloading
-
S
custom rifle suggestions
When I decide to go full on custom, @p_ham is getting the call!! -
S
Savage Ultralite 28 Nosler
This thing hasn't sold yet??!! Great Googly!!! Someone really needs to buy this!! Before I do that is!! -
S
Ebonizing Walnut
My ex-wife stripped the finish off my old Savage 110 wood stock. Once she got the brown paint excuse of a stain off of it, we were amazed at the grain in the wood. She used some white oak stain and polyurethane. I have another wood stock for a 110 that I want to try Shou-sugi-ban on. It's... -
S
Restoring Accuracy, Remington 700
You could always do the same as a radiator cap replacement. Where you take off the radiator cap and pull a different vehicle in. Put radiator cap on. In this case, remove the Remington emblem and put it on a Savage. Lol
